Super Capacitors Monitoring System Using CAN Bus Protocol

Josefina Castañeda-Camacho; Angel Bulmaro-Sánchez; Gerardo Mino-Aguilar; Germán Muñóz; Manuel Tlapa; Daniel Ortiz

doi:doi:10.11648/j.jeee.20170504.13

| Peer-Reviewed

Super Capacitors Monitoring System Using CAN Bus Protocol

Josefina Castañeda-Camacho, Angel Bulmaro-Sánchez, Gerardo Mino-Aguilar, Germán Muñóz, Manuel Tlapa, Daniel Ortiz

Published in Journal of Electrical and Electronic Engineering (Volume 5, Issue 4)

Received: 18 May 2017 Accepted: 12 June 2017 Published: 18 July 2017

Views: Downloads:

Download PDF

Share This Article

Twitter
Linked In
Facebook

Abstract

The present work describes a monitoring system of a bank of supercapacitors (SCB) based on the use of CAN BUS protocol as the data transmission mode. A boost converter with 12.5 V at its output is included to stabilize the voltage in the supercapacitors. This paper provide a basis for the design of a diagnostic systems which aim to monitor the storage, to extend the supercapacitors life cycle and to detect the voltage variations outside the range of operation that could damage the bank. A circuit is implemented in a way that it allows to balance the voltages of the SCB and to avoid a variation of voltage that could cause the destruction of the components. The monitoring system will receive the voltage data of the SCB by means of the CAN bus protocol and show these voltages through a graphical interface in an intelligent screen, the monitoring will allow to detect an over voltage and thus avoid premature damage in these elements.

Published in	Journal of Electrical and Electronic Engineering (Volume 5, Issue 4)
DOI	10.11648/j.jeee.20170504.13
Page(s)	123-129
Creative Commons	This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited.
Copyright	Copyright © The Author(s), 2017. Published by Science Publishing Group

Keywords

CD/CD, Converter, Supercapacitor, Balance Circuit, CAN Bus Network

References

[1]	Daniel W. Hart, “Electrónica de Potencia”, Prentice Hall Hispanoamericana, S. A, Primera Edición, Pag. 226 – 279, 2001.
[2]	Muhammad H. Rsahid, “Electrónica de Potencia, Circuitos dispositivos y aplicaciones”, Prentice Hall Hispanoamericana, S. A, Segunda Edición, Pag. 226 – 279, 1993.
[3]	N Maxwell, Ultracapacitor product guide, Maxwell Technologies Inc, San Diego CA, December 2014.
[4]	http:/electricitystorage.org/tech/technologies_comparisons_lifeefficiency.htm (Accessed on: January 7, 2015).
[5]	Thrap, Guy C. "Charge balancing circuit." U.S. Patent No. 6,806,686, 19 Oct. 2004.
[6]	Robert Bosch GmbH, “CAN Specification Version 2.0”, The Bosch IC Design Centre, Reutingen, DE, 1991.
[7]	Emani, K. C., Kam, K. and Zawodniok, M., ‘Improvement of CAN bus performance by using error correction codes’, 2007 IEEE.
[8]	‘Using CAN Bus Serial Communications in Space Flight Applications’, Intersil white paper, http://www.intersil.com (2016).
[9]	‘ISL7202xSEHEVAL1Z Evaluation Board User Guide’, Intersil document UG051, http://www.intersil.com (2016).
[10]	B. Ling, F. Peng, and A. Li, "The Car Body Control Bus Design Based on CAN/LIN Bus," in Computational and Information Sciences (ICCIS), 2011 International Conference on, 2011, pp. 885-888.
[11]	Kirsch D. (1996) The Electric Car and the Burden of History: Studies in Automotive System Rivalry in the United Stares, 1996.
[12]	American Petroleum institute (API), Alcohols and Ethers, Publication No. 4261, 2^nd ed. (Washington, DC, July 1988), Table B-1, 1988.
[13]	Massot Campos Miguel, “Frenado Regenerativo en vehículos eléctricos mediante supercondensadores”, Revista Automátia e Instrumentación, n. 43, p. 59 – 64, 2011.
[14]	Mera, Isaac Gil. “Diseño de un Sistema de almacenamiento de energía híbrido basado en baterías y supercondensadores para su integración en microredes eléctricas”. Tesis. Escuela Superior de Ingenieros, Universidad de evilla, 2011.
[15]	Baeza Marcos, “Electric Vehicle”, http://blogs.elpais.com/[Research:thursday march 03, 2014], 2011.
[16]	García Gallegos, J. Carlos, Qué son los supercondensadores?, http://papelperiodico.com/[Research:wednesday, march 02, 2014], 2013.
[17]	Mesa Montoya, Carlos Andrés, “Introducción a los Sistemas de Comunicación del vehículo”, http://mgiportal.sena.edu.com/[Research:wednesday, march 10, 2014], 2008.
[18]	Yoong M. K., Gan Y. H., Gan G. D., Leong C. K., Phuan Z. Y., Cheah B. K., & Chew K. W. (2010, November). “Studies of regenerative braking in electric vehicles, in sustainable utilization and development in Engineering and Technology”, IEEE conference on (pp. 40 – 45), 2010.
[19]	Shi L., & Crow M. L. Comparison of Ultracapacitor electric Circuit Models. In Power and Energy Society General Meeting-Conversion and Delivery of Electrical Energy in the 21^st Century. IEEE (pp. 1-6), 2008.
[20]	Paul K., Christian M., Pascal V., Guy C., Gerard R., & Younes Z. “Constant Power Cycling for Accelerated ageing of supercapacitors. In Power Elecronics and Applications”, 2009. EPE’09. 13^th European Conference on (pp. 1-10). IEEE, 2009.
[21]	Barrade P. “Series Connection of Supercapacitors: Comparative Study of Solutions for the Active Equalization of the Voltages”. Proceedings of 7^th international Conference on Modeling and Simulation of Electric Machines, Converters and Systems, IEEE, 2002.
[22]	Qu Y., Zhu J., Hu J., & Holliday B. “Overview of supercapacitor cell voltage balancing methods for an electric vehicle”. In ECCE Asia Downunder (ECCE Asia), IEEE (pp. 810 – 814). IEEE, 2013.
[23]	Ren-gui L., Lei P., Rui M., Jun-lei W., & Chun-bo Z. “EV energy storage monitoring system based on distributed data acquisition”. In Vehicle Power and Propulsion Conference, VPPC’09. IEEE (pp. 1386-1389). IEEE, 2009.
[24]	Joel Shindall “The Charge of the Ultracapacitors Nanotechnology takes energy storage beyond batteries”, IEEE Spectrum, November 2007.
[25]	Glenn Zorpette. Super Charged. “A tiny south Korean company is out make capacitors powerful enough to propel the next generation of hybrit-electric cars”. IEEE Spectrum, January 2005.
[26]	Tonzhen Wei, “Deterioration Diagnosis of Ultracapacitor for Power Electronics Applications”, IEEE, Sydney Australia, Tech, 2008.
[27]	Junseok Song, “A Rapid Charging Station with an Ultracapacitor Energy Storage System for plug – in Electrical vehicles. Department of Electrical and Computer Engineering”, The University of Texas at Austin, USA, 2011.
[28]	Su C. Q. & Zhang D. Q. “Computer simulation Study on Ultracapacitor for Electric Vehicle. In Intelligent Computin and Intelligent Systems”, ICIS 2009. IEEE International Conference on (Vol. 1, pp. 199-203). IEEE, 2009.

Cite This Article

Plain Text BibTeX RIS

APA Style

Josefina Castañeda-Camacho, Angel Bulmaro-Sánchez, Gerardo Mino-Aguilar, Germán Muñóz, Manuel Tlapa, et al. (2017). Super Capacitors Monitoring System Using CAN Bus Protocol. Journal of Electrical and Electronic Engineering, 5(4), 123-129. https://doi.org/10.11648/j.jeee.20170504.13

Copy | Download

ACS Style

Josefina Castañeda-Camacho; Angel Bulmaro-Sánchez; Gerardo Mino-Aguilar; Germán Muñóz; Manuel Tlapa, et al. Super Capacitors Monitoring System Using CAN Bus Protocol. J. Electr. Electron. Eng. 2017, 5(4), 123-129. doi: 10.11648/j.jeee.20170504.13

Copy | Download

AMA Style

Josefina Castañeda-Camacho, Angel Bulmaro-Sánchez, Gerardo Mino-Aguilar, Germán Muñóz, Manuel Tlapa, et al. Super Capacitors Monitoring System Using CAN Bus Protocol. J Electr Electron Eng. 2017;5(4):123-129. doi: 10.11648/j.jeee.20170504.13

Copy | Download

@article{10.11648/j.jeee.20170504.13,
  author = {Josefina Castañeda-Camacho and Angel Bulmaro-Sánchez and Gerardo Mino-Aguilar and Germán Muñóz and Manuel Tlapa and Daniel Ortiz},
  title = {Super Capacitors Monitoring System Using CAN Bus Protocol},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {5},
  number = {4},
  pages = {123-129},
  doi = {10.11648/j.jeee.20170504.13},
  url = {https://doi.org/10.11648/j.jeee.20170504.13},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20170504.13},
  abstract = {The present work describes a monitoring system of a bank of supercapacitors (SCB) based on the use of CAN BUS protocol as the data transmission mode. A boost converter with 12.5 V at its output is included to stabilize the voltage in the supercapacitors. This paper provide a basis for the design of a diagnostic systems which aim to monitor the storage, to extend the supercapacitors life cycle and to detect the voltage variations outside the range of operation that could damage the bank. A circuit is implemented in a way that it allows to balance the voltages of the SCB and to avoid a variation of voltage that could cause the destruction of the components. The monitoring system will receive the voltage data of the SCB by means of the CAN bus protocol and show these voltages through a graphical interface in an intelligent screen, the monitoring will allow to detect an over voltage and thus avoid premature damage in these elements.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - Super Capacitors Monitoring System Using CAN Bus Protocol
AU  - Josefina Castañeda-Camacho
AU  - Angel Bulmaro-Sánchez
AU  - Gerardo Mino-Aguilar
AU  - Germán Muñóz
AU  - Manuel Tlapa
AU  - Daniel Ortiz
Y1  - 2017/07/18
PY  - 2017
N1  - https://doi.org/10.11648/j.jeee.20170504.13
DO  - 10.11648/j.jeee.20170504.13
T2  - Journal of Electrical and Electronic Engineering
JF  - Journal of Electrical and Electronic Engineering
JO  - Journal of Electrical and Electronic Engineering
SP  - 123
EP  - 129
PB  - Science Publishing Group
SN  - 2329-1605
UR  - https://doi.org/10.11648/j.jeee.20170504.13
AB  - The present work describes a monitoring system of a bank of supercapacitors (SCB) based on the use of CAN BUS protocol as the data transmission mode. A boost converter with 12.5 V at its output is included to stabilize the voltage in the supercapacitors. This paper provide a basis for the design of a diagnostic systems which aim to monitor the storage, to extend the supercapacitors life cycle and to detect the voltage variations outside the range of operation that could damage the bank. A circuit is implemented in a way that it allows to balance the voltages of the SCB and to avoid a variation of voltage that could cause the destruction of the components. The monitoring system will receive the voltage data of the SCB by means of the CAN bus protocol and show these voltages through a graphical interface in an intelligent screen, the monitoring will allow to detect an over voltage and thus avoid premature damage in these elements.
VL  - 5
IS  - 4
ER  -

Copy | Download

Author Information

Josefina Castañeda-Camacho
Angel Bulmaro-Sánchez

Electronics Departament, Benemérita Universidad Autónoma de Puebla BUAP, Puebla, México
Gerardo Mino-Aguilar

Electronics Departament, Benemérita Universidad Autónoma de Puebla BUAP, Puebla, México
Germán Muñóz
Manuel Tlapa

Electronics Departament, Benemérita Universidad Autónoma de Puebla BUAP, Puebla, México
Daniel Ortiz

Electronics Departament, Benemérita Universidad Autónoma de Puebla BUAP, Puebla, México

Download PDF

Sections

Plain Text BibTeX RIS

APA Style

Josefina Castañeda-Camacho, Angel Bulmaro-Sánchez, Gerardo Mino-Aguilar, Germán Muñóz, Manuel Tlapa, et al. (2017). Super Capacitors Monitoring System Using CAN Bus Protocol. Journal of Electrical and Electronic Engineering, 5(4), 123-129. https://doi.org/10.11648/j.jeee.20170504.13

Copy | Download

ACS Style

Josefina Castañeda-Camacho; Angel Bulmaro-Sánchez; Gerardo Mino-Aguilar; Germán Muñóz; Manuel Tlapa, et al. Super Capacitors Monitoring System Using CAN Bus Protocol. J. Electr. Electron. Eng. 2017, 5(4), 123-129. doi: 10.11648/j.jeee.20170504.13

Copy | Download

AMA Style

Josefina Castañeda-Camacho, Angel Bulmaro-Sánchez, Gerardo Mino-Aguilar, Germán Muñóz, Manuel Tlapa, et al. Super Capacitors Monitoring System Using CAN Bus Protocol. J Electr Electron Eng. 2017;5(4):123-129. doi: 10.11648/j.jeee.20170504.13

Copy | Download

@article{10.11648/j.jeee.20170504.13,
  author = {Josefina Castañeda-Camacho and Angel Bulmaro-Sánchez and Gerardo Mino-Aguilar and Germán Muñóz and Manuel Tlapa and Daniel Ortiz},
  title = {Super Capacitors Monitoring System Using CAN Bus Protocol},
  journal = {Journal of Electrical and Electronic Engineering},
  volume = {5},
  number = {4},
  pages = {123-129},
  doi = {10.11648/j.jeee.20170504.13},
  url = {https://doi.org/10.11648/j.jeee.20170504.13},
  eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20170504.13},
  abstract = {The present work describes a monitoring system of a bank of supercapacitors (SCB) based on the use of CAN BUS protocol as the data transmission mode. A boost converter with 12.5 V at its output is included to stabilize the voltage in the supercapacitors. This paper provide a basis for the design of a diagnostic systems which aim to monitor the storage, to extend the supercapacitors life cycle and to detect the voltage variations outside the range of operation that could damage the bank. A circuit is implemented in a way that it allows to balance the voltages of the SCB and to avoid a variation of voltage that could cause the destruction of the components. The monitoring system will receive the voltage data of the SCB by means of the CAN bus protocol and show these voltages through a graphical interface in an intelligent screen, the monitoring will allow to detect an over voltage and thus avoid premature damage in these elements.},
 year = {2017}
}

Copy | Download

TY  - JOUR
T1  - Super Capacitors Monitoring System Using CAN Bus Protocol
AU  - Josefina Castañeda-Camacho
AU  - Angel Bulmaro-Sánchez
AU  - Gerardo Mino-Aguilar
AU  - Germán Muñóz
AU  - Manuel Tlapa
AU  - Daniel Ortiz
Y1  - 2017/07/18
PY  - 2017
N1  - https://doi.org/10.11648/j.jeee.20170504.13
DO  - 10.11648/j.jeee.20170504.13
T2  - Journal of Electrical and Electronic Engineering
JF  - Journal of Electrical and Electronic Engineering
JO  - Journal of Electrical and Electronic Engineering
SP  - 123
EP  - 129
PB  - Science Publishing Group
SN  - 2329-1605
UR  - https://doi.org/10.11648/j.jeee.20170504.13
AB  - The present work describes a monitoring system of a bank of supercapacitors (SCB) based on the use of CAN BUS protocol as the data transmission mode. A boost converter with 12.5 V at its output is included to stabilize the voltage in the supercapacitors. This paper provide a basis for the design of a diagnostic systems which aim to monitor the storage, to extend the supercapacitors life cycle and to detect the voltage variations outside the range of operation that could damage the bank. A circuit is implemented in a way that it allows to balance the voltages of the SCB and to avoid a variation of voltage that could cause the destruction of the components. The monitoring system will receive the voltage data of the SCB by means of the CAN bus protocol and show these voltages through a graphical interface in an intelligent screen, the monitoring will allow to detect an over voltage and thus avoid premature damage in these elements.
VL  - 5
IS  - 4
ER  -

Copy | Download