A long time ago, nature proved that even the hardest engineering materials change their shape and form when water is applied to them. The new shape formed by this phenomenon can be both valuable and/or attractive. In modern industry, water cutting technology is divided into two groups. Water jet cutting technology, which is cutting with pure water and abrasive water jet cutting technology, which uses water embedded with fine abrasive particles. Clean water jet cutting technology is suitable for “soft engineering materials” for instance paper, wood, textiles, food and plastic. It is extensively used technology in industries to cut almost everything from frozen chickens to one-use diapers. On the other hand, when “hard engineering materials” need to be cut, the addition of fine abrasive particles such as garnet allows one to cut almost any engineering material whether it be marble (as used in Al-Masjid Al-Haram, The Holy Mosque, in Makkah, KSA) or tool steel, and in thickness up to 200 mm. In this review paper, the primary objective is to highlight the state-of-the-art of the abrasive water jet cutting technology and the promise for micro- and nano-machining in modern industry.
| Published in | International Journal of Mechanical Engineering and Applications (Volume 5, Issue 1) |
| DOI | 10.11648/j.ijmea.20170501.11 |
| Page(s) | 1-14 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2017. Published by Science Publishing Group |
Abrasive Water Jet Cutting, AWJC, Micro- and Nano-Machining
| [1] | Wang, J. and W. C. K. Wong, A study of abrasive waterjet cutting of metallic coated sheet steels. International Journal of Machine Tools and Manufacture, 1999. 39(6): p. 855-870. |
| [2] | Krajcarz, D., Comparison Metal Water Jet Cutting with Laser and Plasma Cutting Procedia Engineering, 2014. 69 p. 838 - 843. |
| [3] | ŘEPKA, M., et al., Automated System for Prediction of Technological Parameters of Abrasive Water Jet Cutting Mechanism. GeoScience Engineering, 2010. LVI(4): p. 17-21. |
| [4] | Birtu, C. and V. Avramescu, Abrasive water jet cutting - technique, equipment, performances. Nonconventional Technologies Review, 2012. 16(1): p. 40-46. |
| [5] | Valíček, J., et al., Proposition of a Solution for the Setting of the Abrasive Waterjet Cutting Technology, in Measurement Science Review. 2013. p. 279. |
| [6] | Chithirai, P. S. M. and S. R. N. Mohanna, Abrasive Waterjet Cutting Surfaces of Ceramics - An Experimental Investigation. International Journal of Applied Science, Technology and Engineering Research, 2012. 1(3): p. 52-59. |
| [7] | Momber, A. W. and R. Kovacevic, Principles of Abrasive Water Jet Machining. 1st edition. 1998, London: Springer-Verlag London. |
| [8] | Lebar, A. and M. Junkar, Simulation of abrasive water jet cutting process: Part 1. Unit event approach. Modelling Simul. Mater. Sci. Eng., 2004. 12: p. 1159-1170. |
| [9] | Momber, A. W., The kinetic energy of wear particles generated by abrasive–water-jet erosion. Journal of Materials Processing Technology, 1998. 83(1–3): p. 121-126. |
| [10] | Hashish, M., A model for abrasive waterjet (AWJ) machining. Transactions of ASME Journal of Engineering Materials and Technology, 1989. III: p. 154-162. |
| [11] | Prasad, K. S. and G. Chaitanya, The Research Review on Abrasive Machining International Journal on Recent Technologies in Mechanical and Electrical Engineering (IJRMEE), 2016. 3(6): p. 19-27. |
| [12] | Aswathy, K. and P. Govindan, Modeling of Abrasive Water Jet Machining Process. International Journal of Recent advances in Mechanical Engineering (IJMECH) 2015. 4(3): p. 59-71. |
| [13] | Gerencser, K. and L. Bejo, Investigations into the waterjet cutting of solid wood. Wood Research, 2007. 52(2): p. 57-64. |
| [14] | Hashish, M., Optimization Factors in Abrasive-Waterjet Machining. Journal of Engineering for Industry, 1991. 113(1): p. 29-37. |
| [15] | Hloch, S. and S. Fabian, Abrasive water jet process factors influence on stainless steel AISI 304 macrogeometrical cutting duality, In: Scientific Bulletin: Serie C. Volume 19: Mechanics, Tribology, Machine Manufacturing Technology. North University of Baia Mare, Romania. 2005. p. 261-266. |
| [16] | Wang, J. and D. M. Guo, The cutting performance in multi pass abrasive water jet machining of industrial ceramics. Journal of Materials Processing Technology, 2003. 133: p. 371-377. |
| [17] | Klichova, D. and J. Klich, Study of the Effect of Material Machinability on Quality of Surface Created by Abrasive Water Jet. Procedia Engineering, 2016. 149: p. 177-182. |
| [18] | Kovacevic, R., Monitoring the depth of abrasive waterjet penetration. International Journal of Machine Tools & Manufacture, 1992. 32(5): p. 725-736. |
| [19] | Hashish, M., Optimization factors in abrasive waterjet machining. Transaction of ASME J. Eng. Ind., 1991. 113: p. 29-37. |
| [20] | John Rozario Jegaraj J. and R. B. N., A soft computing approach for controlling the quality of cut with abrasive waterjet cutting system experiencing orifice and focusing tube wear. Journal of Materials Processing Technology, 2007. 185(1-3): p. 217-227. |
| [21] | Shanmugam, D. K., J. Wang, and H. Liu, Minimization of kerf tapers in abrasive waterjet machining of alumina ceramics using a compensation technique. International Journal of Machine Tools and Manufacture, 2008. 48: p. 1527-1534. |
| [22] | Shanmugam, D. K. and S. H. Masood, An investigation of kerf characteristics in abrasive waterjet cutting of layered composites. International Journal of Material Processing Technology 2009. 209: p. 3887-3893. |
| [23] | Lemma, E., et al., Optimising the AWJ cutting process of ductile materials using nozzle oscillation technique. International Journal of Machine Tools and Manufacture, 2002. 42: p. 781-789. |
| [24] | Fenggang, L., E. S. Geskin, and L. Tismenetskiy, Feasibility study of abrasive waterjet polishing, in 13th Int. Conf. on Jetting Technology. 1996: Sardinia. p. 709-723. |
| [25] | Hashish, M., Turning with abrasive-waterjets - a first investigation. Trans. ASME, Journal of Engineering for Industry, 1987. 109: p. 281-290. |
| [26] | Yong, Z. and R. Kovacevic, Modeling of jetflow drilling with consideration of the chaotic erosion histories of particles. Wear, 1997. 209: p. 284-291. |
| [27] | Hashish, M., An investigation of milling with abrasive-waterjets. Trans. ASME, Journal of Engineering for Industry, 1989. 111(2): p. 158-166. |
| [28] | Borkowski, P., Theoretical and experimental basis of hydro-jet surface treatment. 2004, Koszalin. |
| [29] | Hashish, M., A Modeling Study of Metal Cutting with Abrasive Water Jets. Transaction of ASME: Journal of Engineering Materials and Technology, 1984. 106(1): p. 88-100. |
| [30] | Hascalik, A., U. Caydas, and H. Gurun, Effect of traverse speed on abrasive waterjet machining of Ti-6Al-4V alloy. Meter. Des., 2007. 28: p. 1953-1957. |
| [31] | Momber, A. and R. Kovacevic, Principles of Abrasive Waterjet Machining. 1998, London: Springer-Verlag. |
| [32] | Zen, J. and T. J. Kim, Parameter prediction and cost analysis in abrasive waterjet cutting operations, in 7th American Water Jet Conf., Seattle, Editor. 1993: Washington. p. 175-189. |
| [33] | Alsoufi, M. S., Mohammed W. Alhazmi, Hamza A. Ghulman, Shadi M. Munshi and Sufyan Azam. Surface Roughness and Knoop Indentation Micro-Hardness Behavior of Aluminium Oxide (Al2O3) and Polystyrene (C8H8)n Materials. International Journal of Mechanical & Mechatronics Engineering, 2016. 16(6): p. 43-49. |
| [34] | Siores, E., et al., Enhancing abrasive waterjet cutting of ceramics by head oscillation techniques. Ann CIRP, 1996. 45(1): p. 215-218. |
| [35] | Mostafa, M. A. G., Mohammad S. Alsoufi, and Bassam A. Tayeb, CAD/CAM Integration Based on Machining Features for Prismatic Parts. International Journal of Emerging Trends & Technology in Computer Science, 2015. 4(3): p. 106-110. |
| [36] | Aydiner, K., Abrasive Water Jet Cutting of Granite. Powder Metallurgy & Mining, 2014. 3(2): p. 1000e130. |
| [37] | Azmir, M. A. and A. K. Ahsan, Investigation on glass/epoxy composite surfaces machined by abrasive waterjet machining. Journal of Materials Processing Technology, 2008. 198: p. 122-128. |
| [38] | Ma, C. and R. T. Deam, A correlation for predicting the kerf profile from abrasive waterjet cutting. Experimental Thermal and Fluid Science, 2006. 30: p. 337-343. |
| [39] | Palleda, M., A study of taper angles and material removal rates of drilled holes in the abrasive water jet machining process. Journal of Materials Processing Technology, 2007. 189(1–3): p. 292-295. |
| [40] | Chung, Y., E. S. Geskin, and P. J. Singh, Prediction of the geometry of the kerf created in the course of abrasive waterjet machining of ductile materials, in 11th Int. Conf. on Jet Cutting Technology, S. Andrews, Editor. 1992: Scotland. p. 525-541. |
| [41] | Zhang, S., et al., Use of pre-profiling a milled pocket as a means of improving machining and lowering energy costs, in 2007 WJTA Conference and Expo, Houston, Editor. 2007: Texas. Paper 3-H. |
| [42] | Hashish, M., On the modeling of abrasive-waterjet cutting, in 7th Int. Symposium. on Jet Cutting Technology, Ottawa, Editor. 1984: Canada. p. 249-265. |
| [43] | Zeng, J. and T. J. Kim, Development of an abrasive waterjet kerf cutting model for brittle materials, in 11th Int. Conf. on Jet Cutting Technology, S. Andrews, Editor. 1992: Scotland. p. 483-501. |
| [44] | Alsoufi, M. S., Dhia K. Suker, Abdulaziz S. Alsabban, and Sufyan Azam, Experimental Study of Surface Roughness and Micro-Hardness Obtained by Cutting Carbon Steel with Abrasive WaterJet and Laser Beam Technologies. American Journal of Mechanical Engineering, 2016. 4(5): p. 173-181. |
| [45] | Feng, Y. X., et al., An Experimental Study on Milling Al2O3 Ceramics with Abrasive Waterjet. Key Engineering Materials, 2007. 339: p. 500-504. |
| [46] | Snider, D. and M. Hashish, AWJ trimming of composites and cutting of other materials using 6-axis robots, in WJTA-IMCA Conference and Expo. 2011: Houston, Texas, Paper A3. |
| [47] | Lauand, V. H., W. T. Hennies, and A. J. Stellin, Glass and marble (cachoeiro de itapemirim) milling with abrasive water jetting, in 19th Int. Conference Water Jetting, B. Group, Editor. 2008: Nottingham. p. 121-139. |
| [48] | Abdullah, R., A. Mahrous, and A. Barakat, Surface quality of marble machined by abrasive water jet. Cogent Engineering, 2016. 3(1): p. 1178626. |
| [49] | Borkowski, P. J., Application of Abrasive-Water Jet Technology for Material Sculpturing. Transactions of the Canadian Society for Mechanical Engineering, 2010. 34(3-4): p. 389-400. |
| [50] | Badgujar, P. P. and M. G. Rathi, Abrasive Waterjet Machining-A State of Art IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) 2014. 11(3): p. 59-64. |
| [51] | Kvietková, M., Š. Barcík, and M. Gašparík, Optimization of the Cutting Process of Wood-Based Agglomerated Materials by Abrasive Water-Jet. Acta Silvatica et Lignaria Hungarica, 2014. 10(1): p. 31-47. |
| [52] | Brandt, C. and H. Louis, Influence of the nozzlegeometry on abrasive water jets, in Proc. of the 5th Int. Conf. on Water Jet Tech. 1998: New Delhi, India. p. 330-344. |
| [53] | Alsoufi, M. S. and T. M. Bawazeer, The Effect of Aggressive Biological Materials on a Painted Automotive Body Surface Roughness. American Journal of Nano Research and Applications, 2015. 3(2): p. 17-26. |
| [54] | Alsoufi, M. S. and T. M. Bawazeer, Quantifying assessment of touch-feel perception: an investigation using stylus base equipment and self-touch (human fingertip). Umm Al-Qura University: Journal of Engineering and Architecture, 2015. 1(1): p. 1-16. |
| [55] | Suker, D. K., M. S. Alsoufi, M. M. Alhusaini, S. A. Azam, Studying the Effect of Cutting Conditions in Turning Process on Surface Roughness for Different Materials. World Journal of Research and Review (WJRR), 2016. 2(4): p. 16-21. |
| [56] | Alsoufi, M. S., A high dynamic response micro-tribometer measuring-head, in School of Engineering. 2011, University of Warwick: Coventry. |
| [57] | Jerman, M., et al., The Study of Abrasive Water Jet Cutting Front Development using a Two-Dimensional Cellular Automata Model. Journal of Mechanical Engineering 2015. 61 (5): p. 292-302. |
| [58] | Akkurt, A., Experimental Investigation of the Surface Properties Obtained by Cutting Brass-353 (α+β) with an Abrasive Water Jet and other Cutting Methods. Materials and technology, 2014. 48 (5): p. 725-734. |
| [59] | Sonawane, N. K., M. Y. Khalkar, and V. B. Shinde, A Review on Parameters Optimization in Abrasive Water Jet Cutting International Journal of Innovative and Emerging Research in Engineering 2016. 3(2): p. 11-14. |
| [60] | Lohar, S. R. and P. R. Kubade, Current Research and Development in Abrasive Water Jet Machining (AWJM): A Review International Journal of Science and Research (IJSR) 2016. 5(1): p. 996-999. |
| [61] | Batra, T. and Devilal, Literature Review on Abrasive Jet Machining International Journal of Research in Aeronautical and Mechanical Engineering, 2015. 3(12): p. 26-32. |
| [62] | Pawar, T., S. Wagh, and R. Shinde, Literature Review on Abrasive Jet Machining International Journal of Engineering Research and General Science, 2015. 3(3): p. 1047-1051. |
| [63] | Sreekesh, K. and P. Govindan, A Review on Abrasive Water Jet Cutting. International Journal of Recent advances in Mechanical Engineering (IJMECH), 2014. 3(3): p. 153-158. |
| [64] | Srikanth, D. V. and M. S. Rao, Abrasive Jet Machining – Research Review. International Journal of Advanced Engineering Technology, 2014. V(II): p. 18-24. |
| [65] | Bagla, S., D. Bhardwaj, and Sachin, A Review on Machining of Granite by Abrasive Water Jet. International Journal of Enhanced Research in Science Technology & Engineering. 2014. 3 (4): p. 362-364. |
| [66] | Saxena, V., R. S. Jadoun, and S. Gupta, A Review Paper on most Significant and Sub Significant Parameters of Abrasive Water Jet Machining International Journal of Advance Research in Science and Engineering, 2015. 4(1): p. 249-256. |
| [67] | Shah, R. V. and D. M. Patel, Abrasive Water Jet Machining – The Review International Journal of Engineering Research and Applications, 2012. 2(5): p. 803-806. |
| [68] | Verma, S., S. K. Moulick, and S. K. Mishra, Nozzle Wear Parameter in Water jet machining The Review International Journal of Engineering Development and Research, 2014. 2(1): p. 1063-1073. |
| [69] | Sharma, A., et al., A-Rectroscopic Review - Optimization of Abrasive Water Jet Machining International Journal of Research in Advent Technology, 2016. 4(3): p. 233-237. |
| [70] | Patel, S. R. and A. A. Shaikh, A Review on Machining of Fiber Reinforced Plastic using Abrasive Waterjet International Journal of Innovative Technology & Adaptive Management (IJITAM), 2013. 1(3): p. 1-8. |
| [71] | Mhamunkar, M. M., N. Raut, and J. Chavan, A Review on Research and Development in Optimization of Parameter of Abrasive Waterjet Machining International Journal of Advanced Research in Science, Engineering and Technology, 2016. 3(3): p. 1616-1620. |
| [72] | Abrão, A. M., et al., Drilling of fiber reinforced plastics: A review. Journal of Materials Processing Technology, 2007. 186(1–3): p. 1-7. |
| [73] | Molitoris, M., et al., A Review of Research on Water Jet with Slurry Injection. Procedia Engineering, 2016. 149: p. 333-339. |
| [74] | Li, R., et al., Pressure, Feed Rate, and Abrasive Mass Flow Rate Influence on Surface Roughness for Recombinant Bamboo Abrasive Water Jet Cutting. BioResources, 1998. 10(2): p. 1998-2008. |
| [75] | Monková, K., et al., Factor Analysis of The Abrasive Water Jet Factors Affecting the Surface Roughness of Titanium. Technical Gazette, 2011. 18(1): p. 83-88. |
| [76] | Mutavgjic, V., et al., Experimental Investigation of Surface Roughness Obtained by Abrasive Water Jet Machining, in 15th International Research/Expert Conference "Trends in the Development of Machinery and Associated Technology" TMT 201, Prague, Editor. 2011: Czech Republic. |
| [77] | Selvan, M. C. P. and N. M. S. Raju, Analysis of Surface Roughness in Abrasive Water Jet Cutting Of Cast Iron. International Journal of Science, Environment and Technology, 2012. 1(3): p. 174 - 182. |
| [78] | Shanmughasundaram, P., Influence of Abrasive Water jet machining parameters on surface roughness of Eutectic Al-Si Alloy-Graphite Composites. Journal of Materials Physics and Mechanics, 2014. 19: p. 1-8. |
| [79] | Doreswamy, D., et al., Machining of D2 Heat treated steel using AWJ: Effect of Standoff distance and feed rate on kerf width and surface roughness. International Journal of Research in Engineering and Technology, 2014. 3(8): p. 417-421. |
| [80] | Begic-Hajdarevic, D., et al., Experimental Study on Surface Roughness in Abrasive Water Jet Cutting. Procedia Engineering, 2015. 100: p. 394-399. |
| [81] | Patel, V. B. and V. A. Patel, Parametric analysis of Abrasives water jet machining of EN8 Material. International Journal of Engineering Research and Applications (IJERA), 2012. 2(3): p. 3029-3032. |
| [82] | Alberdi, A., et al., Composite Cutting with Abrasive Water Jet. Procedia Engineering, 2013. 63: p. 421-429. |
| [83] | Folkes, J., Water jet-An Innovative Tool for Manufacturing. Journal of Materials Processing Technology, 2009. 209: p. 6181- 6189. |
| [84] | Aultrin, K. S. J. and M. D. Anand, Optimization of Machining Parameters in AWJM Process for an Copper Iron Alloy Using RSM and Regression Analysis. International Journal of Emerging Engineering Research and Technology, 2014. 2 (5): p. 19-34. |
| [85] | Deng, J. L., The introduction to grey system theory. J Grey System, 1989. 1(1): p. 1-24. |
| [86] | Yunus, M. and M. S. Alsoufi, Multi-Objective Optimization of Joint Strength of Dissimilar Aluminum Alloys Formed by Friction Stir Welding Using Taguchi-Grey Relation Analysis International Journal of Engineering & Technology IJET-IJENS, 2016. 16(04): p. 10-17. |
| [87] | Yunus, M. and M. S. Alsoufi, Multi-output optimization of tribological characteristics control factors of thermally sprayed industrial ceramic coatings using hybrid Taguchi-grey relation analysis. Friction, 2016. 4(3): p. 208-216. |
| [88] | Yunus, M. and M. S. Alsoufi, A Statistical Analysis of Joint Strength of Dissimilar Aluminium Alloys Formed By Friction Stir Welding Using Taguchi Design Approach, Anova For The Optimization Of Process Parameters. IMPACT: International Journal of Research in Engineering & Technology (IMPACT: IJRET), 2015. 3(7): p. 63-70. |
| [89] | Yunus, M., M. S. Alsoufi, and S. M. Munshi, Taguchi-Grey relation analysis for assessing the optimal set of control factors of thermal barrier coatings for high-temperature applications. Mechanics of Advanced Materials and Modern Processes, 2016. 2(1): p. 4. |
| [90] | Yunus, M., M. S. Alsoufi, and M. S. Mustafa, Application of Taguchi Design Approach in the Optimization of Die Design Parameters of a Two Cavity Injection Molding Tool for a Fan Blade Back Cover International Journal in IT and Engineering (IJITE), 2015. 3(7): p. 11-20. |
| [91] | Nagdeve, L., V. Chaturvedi, and J. Vimal, Implementation of Taguchi approach for optimization of abrasive water jet machining process parameters. International Journal of Instrumentation, Control and Automation (IJICA), 2012. 1 (3-4): p. 9-13. |
| [92] | Ramprasad, G. Upadhyay, and K. Hassan, Optimization MRR Of Stainless Steel 403 In Abrasive Water Jet Machining Using Anova And Taguchi Method. International Journal of Engineering Research and Applications, 2015. 5(5): p. 86-91. |
| [93] | Gupta, V., et al., Minimization of Kerf Taper Angle and Kerf Width Using Taguchi's Method in Abrasive Water Jet Machining of Marble. Procedia Materials Science, 2014. 6: p. 140-149. |
| [94] | Reddy, D. S., A. S. Kumar, and M. S. Rao, Parametric Optimization of Abrasive Water Jet Machining of Inconel 800H Using Taguchi Methodology. Universal Journal of Mechanical Engineering, 2014. 2(5): p. 158-162. |
| [95] | Rao, M. S., S. Ravinder, and A. S. Kumar, Parametric Optimization of Abrasive Water jet Machining for Mild Steel: Taguchi Approach. International Journal of Current Engineering and Technology, 2014 (Special Issue-2): p. 28-30. |
| [96] | Chauhan, D. K. and K. K. Chauhan, Optimization of Machining Parameters of Titanium Alloy for Tool Life. 2013, 2013. 2(6): p. 9. |
| [97] | Raval, M. A. and C. P. Patel, Parametric Optimization of Magnetic Abrasive Water Jet Machining of AISI 52100 Steel Using Grey Relational Analysis. International Journal of Engineering Research and Applications (IJERA), 2013. 3(4): p. 527-530. |
| [98] | Preeti, et al., Measuring Material Removal Rate of Marble by Using Abrasive Water Jet Machining. IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) 2013: p. 45-49. |
| [99] | Ganesan, H., et al., Optimization of machining parameters in turning process using genetic algorithm and particle swarm optimization with experimental verification. International Journal of Engineering Science and Technology, 2012. 3(2): p. 1091-1102. |
| [100] | Yusup, N., A. M. Zain, and S. Z. M. Hashim, Evolutionary techniques in optimizing machining parameters: Review and recent applications (2007–2011). Expert Systems with Applications, 2012. 39(10): p. 9909-9927. |
| [101] | Jain, N. K., V. K. Jain, and K. Deb, Optimization of Process Parameters of Mechanical Type Advanced Machining Processes Using Genetic Algorithms. International Journal of Machine Tools & Manufacture, 2007. 47: p. 900-919. |
| [102] | Zain, A. M., H. Haron, and S. Sharif, Optimization of process parameters in the abrasive waterjet machining using integrated SA–GA. Applied Soft Computing, 2011. 11(8): p. 5350-5359. |
| [103] | Venkata Rao, R. and V. D. Kalyankar, Parameter optimization of modern machining processes using teaching–learning-based optimization algorithm. Engineering Applications of Artificial Intelligence, 2013. 26(1): p. 524-531. |
| [104] | Zain, A. M., H. Haron, and S. Sharif, Optimization of process parameters in the abrasive waterjet machining using integrated SA-GA. Appl. Soft Comput., 2011. 11(8): p. 5350-5359. |
| [105] | Vundavilli, P. R., et al., Fuzzy logic-based expert system for prediction of depth of cut in abrasive water jet machining process. Knowledge-Based Systems, 2012. 27: p. 456-464. |
| [106] | Aultrin, K. S. J., M. D. Anand, and P. Jose, Modelling the Cutting Process and Cutting Performance in Abrasive Water Jet Machining Using Genetic-Fuzzy Approach. Procedia Engineering, 2012. 38: p. 4013-4020. |
| [107] | Kesharwani, E. G. S., Controlled Depth Milling of Ti-6Al-4V Alloy using Non-spherical (Triangular & Trapezoidal) Sharp edge shape ceramics abrasive particle in Abrasive Water Jet Machining. International Journal of Scientific & Engineering Research, 2015. 6(5): p. 183-188. |
| [108] | Liu, D., et al., Modeling and optimization of operating parameters for abrasive waterjet turning alumina ceramics using response surface methodology combined with Box–Behnken design. Ceramics International, 2014. 40(6): p. 7899-7908. |
| [109] | Ibraheem, H. M. A., A. Iqbal, and M. Hashemipour, Numerical optimization of hole making in GFRP composite using abrasive water jet machining process. Journal of the Chinese Institute of Engineers, 2015. 38(1): p. 66-76. |
| [110] | Aich, U., et al., Abrasive Water Jet Cutting of Borosilicate Glass. Procedia Materials Science, 2014. 6: p. 775-785. |
| [111] | Dittrich, M., et al., Process Analysis of Water Abrasive Fine Jet Structuring of Ceramic Surfaces via Design of Experiment. Procedia CIRP, 2014. 14: p. 442-447. |
| [112] | Selvan, M. C. P., N. M. S. Raju, and R. Rajavel, Effects of Process Parameters on Depth of Cut in Abrasive Waterjet Cutting of Cast Iron International Journal of Scientific & Engineering Research, 2011. 2(9): p. 1-5. |
| [113] | Mohamed, M. A. K., Waterjet Cutting up to 900 MPa. 2004, Universität Hannover, Germany. p. 1-136. |
| [114] | Ćojbašić, Ž., et al., Surface roughness prediction by extreme learning machine constructed with abrasive water jet. Precision Engineering, 2016. 43: p. 86-92. |
| [115] | Shiou, F.-J. and A. Asmare, Parameters optimization on surface roughness improvement of Zerodur optical glass using an innovative rotary abrasive fluid multi-jet polishing process. Precision Engineering, 2015. 42: p. 93-100. |
| [116] | Löschner, P., K. Jarosz, and P. Niesłony, Investigation of the Effect of Cutting Speed on Surface Quality in Abrasive Water Jet Cutting of 316L Stainless Steel. Procedia Engineering, 2016. 149: p. 276-282. |
| [117] | Kartal, F., Z. Yerlikaya, and H. Gökkaya, Effects of machining parameters on surface roughness and macro surface characteristics when the machining of Al-6082 T6 alloy using AWJT. Measurement, 2017. 95: p. 216-222. |
| [118] | Duspara, M., et al., Influence of Abrasive Feeding and Cutting Direction on the Surface Roughness. Procedia Engineering, 2016. 149: p. 48-55. |
APA Style
Mohammad S. Alsoufi. (2017). State-of-the-Art in Abrasive Water Jet Cutting Technology and the Promise for Micro- and Nano-Machining. International Journal of Mechanical Engineering and Applications, 5(1), 1-14. https://doi.org/10.11648/j.ijmea.20170501.11
ACS Style
Mohammad S. Alsoufi. State-of-the-Art in Abrasive Water Jet Cutting Technology and the Promise for Micro- and Nano-Machining. Int. J. Mech. Eng. Appl. 2017, 5(1), 1-14. doi: 10.11648/j.ijmea.20170501.11
AMA Style
Mohammad S. Alsoufi. State-of-the-Art in Abrasive Water Jet Cutting Technology and the Promise for Micro- and Nano-Machining. Int J Mech Eng Appl. 2017;5(1):1-14. doi: 10.11648/j.ijmea.20170501.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.ijmea.20170501.11,
author = {Mohammad S. Alsoufi},
title = {State-of-the-Art in Abrasive Water Jet Cutting Technology and the Promise for Micro- and Nano-Machining},
journal = {International Journal of Mechanical Engineering and Applications},
volume = {5},
number = {1},
pages = {1-14},
doi = {10.11648/j.ijmea.20170501.11},
url = {https://doi.org/10.11648/j.ijmea.20170501.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ijmea.20170501.11},
abstract = {A long time ago, nature proved that even the hardest engineering materials change their shape and form when water is applied to them. The new shape formed by this phenomenon can be both valuable and/or attractive. In modern industry, water cutting technology is divided into two groups. Water jet cutting technology, which is cutting with pure water and abrasive water jet cutting technology, which uses water embedded with fine abrasive particles. Clean water jet cutting technology is suitable for “soft engineering materials” for instance paper, wood, textiles, food and plastic. It is extensively used technology in industries to cut almost everything from frozen chickens to one-use diapers. On the other hand, when “hard engineering materials” need to be cut, the addition of fine abrasive particles such as garnet allows one to cut almost any engineering material whether it be marble (as used in Al-Masjid Al-Haram, The Holy Mosque, in Makkah, KSA) or tool steel, and in thickness up to 200 mm. In this review paper, the primary objective is to highlight the state-of-the-art of the abrasive water jet cutting technology and the promise for micro- and nano-machining in modern industry.},
year = {2017}
}
TY - JOUR T1 - State-of-the-Art in Abrasive Water Jet Cutting Technology and the Promise for Micro- and Nano-Machining AU - Mohammad S. Alsoufi Y1 - 2017/01/12 PY - 2017 N1 - https://doi.org/10.11648/j.ijmea.20170501.11 DO - 10.11648/j.ijmea.20170501.11 T2 - International Journal of Mechanical Engineering and Applications JF - International Journal of Mechanical Engineering and Applications JO - International Journal of Mechanical Engineering and Applications SP - 1 EP - 14 PB - Science Publishing Group SN - 2330-0248 UR - https://doi.org/10.11648/j.ijmea.20170501.11 AB - A long time ago, nature proved that even the hardest engineering materials change their shape and form when water is applied to them. The new shape formed by this phenomenon can be both valuable and/or attractive. In modern industry, water cutting technology is divided into two groups. Water jet cutting technology, which is cutting with pure water and abrasive water jet cutting technology, which uses water embedded with fine abrasive particles. Clean water jet cutting technology is suitable for “soft engineering materials” for instance paper, wood, textiles, food and plastic. It is extensively used technology in industries to cut almost everything from frozen chickens to one-use diapers. On the other hand, when “hard engineering materials” need to be cut, the addition of fine abrasive particles such as garnet allows one to cut almost any engineering material whether it be marble (as used in Al-Masjid Al-Haram, The Holy Mosque, in Makkah, KSA) or tool steel, and in thickness up to 200 mm. In this review paper, the primary objective is to highlight the state-of-the-art of the abrasive water jet cutting technology and the promise for micro- and nano-machining in modern industry. VL - 5 IS - 1 ER -
Email: