Hand-held power tools, such as percussive riveting tools, produce vibrational forces that are transmitted through the hands, arms, and elbows. These vibrational forces may be responsible for the causation of short and long-term neuronal and/or vascular diseases. Personal protective materials are available commercially, some of which are used during the operation of percussive power tools (e.g., anti-vibration gloves). In previous studies, D3O® materials showed a greater absorption of impact energy in low-velocity static impact testing compared to conventional materials. In this study, D3O® materials were tested under dynamic impact loadings to evaluate resistance to impact characteristics to assess the adequacy of an ergonomic intervention using D3O® materials. An experiment was performed to evaluate material resistance to impact by evaluating the peak load values with different precompression magnitudes and loading frequencies. D3O® materials showed that compression magnitude was a statistically significant factor (p = 0.00) affecting the peak load value compared to loading frequency, which had little to no effect when tested under 14 Hz or less. As peak loads increase, the resistance to impact loading decreases and energy transmission increases. D3O® back protector (DBP) and D3O® Rifle Harness (DRH) exhibited lower peak values compared to D3O® Recoil Pad (DRP) material. D3O® materials may be considered to be utilized in a riveting and bucking intervention to reduce vibrational forces from percussive tools in a dynamic aircraft manufacturing environment.
| Published in | American Journal of Aerospace Engineering (Volume 10, Issue 1) |
| DOI | 10.11648/j.ajae.20231001.11 |
| Page(s) | 1-10 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2023. Published by Science Publishing Group |
D3O® Material, Dynamic Impact Loading, Peak Load and Impact Resistance, Recovery Time
| [1] | Griffin, M. J., (1990). Handbook of Human Vibration. Academic Press Limited: London. |
| [2] | Kihlberg, S. & Hagberg, M. (1997). Hand-arm symptoms related to impact and nonimpact hand-held power tools, International Archives of Occupational and, Environmental Health, 69, 282-288. |
| [3] | Dale, A. M., Rohn, A. E., Burwell, A., Shannon, W., Standeven, J., Patton, A., & Evanoff, B. (2011). Evaluation of anti-vibration interventions for the hand during sheet metal assembly work. Work, 39 (2), 169-176. |
| [4] | Pelmear, P. L. (1998). Epidemiology of hand-arm vibration syndrome. Hand–Arm Vibration: a Comprehensive Guide for Occupational Health Professionals, 103-126. |
| [5] | Pelmear, P. L., & Leong, D. (2000). Review of occupational standards and guidelines for hand-arm (segmental) vibration syndrome (HAVS). Applied Occupational and Environmental Hygiene, 15 (3), 291-302. DOI 10.1007/978-1-4614-1150-5_15. |
| [6] | Farkkila, M. (1978). Grip force in vibration disease. Scandinavian Journal of Work, Environment and Health, 4, 159-166. |
| [7] | Burdorf, A. & Monster, A. (1991). Exposure to vibration and self-reported health complaints of riveters in the aircraft industry, Annals of Occupational Hygiene, 35, 287- 298. |
| [8] | Bonvenzi, M., Fiorito, A., & Volpe, C. (1987). Bone and joint disorders in the upper extremities of chipping and grinding operators. International Archives of Occupational and Environmental Health, 50, 189-198. |
| [9] | Dandanell, R., & Engström, K. (1986). Vibration from riveting tools in the frequency range 6 Hz—10 MHz and Raynaud's phenomenon. Scandinavian journal of work, environment & health, 338-342. |
| [10] | Van Rijn, R. M., Huisstede, B. M., Koes, B. W., & Burdorf, A. (2009). Associations between work-related factors and the carpal tunnel syndrome—a systematic review. Scandinavian journal of work, environment & health, 19-36. https://doi.org/10.5271/sjweh.1306. |
| [11] | Palmer, K. T., Harris, E. C., & Coggon, D. (2007). Carpal tunnel syndrome and its relation to occupation: a systematic literature review. Occupational Medicine, 57 (1), 57-66. |
| [12] | Nilsson, T., Wahlström, J., & Burström, L. (2017). Hand-arm vibration and the risk of vascular and neurological diseases—a systematic review and meta-analysis. PLoS One, 12 (7), e0180795. https://doi.org/10.1371/journal.pone.0180795. |
| [13] | Melhorn, J. M. (1996). A prospective study for upper-extremity cumulative trauma disorders of workers in aircraft manufacturing. Journal of Occupational and Environmental Medicine, 38 (12), 1264-1271. |
| [14] | Budd, D., & House, R. (2017). Examining the usefulness of ISO 10819 anti-vibration glove certification. Annals of work exposures and health, 61 (2), 137-140. |
| [15] | Bouix, R., Viot, P., & Lataillade, J. L. (2009). Polypropylene foam behaviour under dynamic loadings: Strain rate, density and microstructure effects. International journal of impact engineering, 36 (2), 329-342. https://doi.org/10.1016/j.ijimpeng.2007.11.007. |
| [16] | Tyler, D. J., & Venkatraman, P. D. (2012, May). Impact resistant materials and Design Principles for Sportswear. In Proceedings of the 88th Textile Institute World Conference: Bridging Innovation, Research and Enterprise. The Textile Institute. ISBN 9781622763443. |
| [17] | Kajtaz, M., & Subic, A. (2015). Experimental investigation into suitability of smart polymers As an impact-absorbing material for an improved rugby headgear. In Proceedings of International Conference on Mechanics, Materials, Mechanical Engineering and Chemical Engineering pp. 62-74. |
| [18] | Venkatraman, P., & Tyler, D. (2015). Impact-Resistant Materials and Their Potential. Materials and Technology for Sportswear and Performance Apparel, 205-230. |
| [19] | Tang, M., Huang, G., Zhang, H., Liu, Y., Chang, H., Song, H., & Wang, Z. (2017). Dependences of Rheological and Compression Mechanical Properties on Cellular Structures for Impact-Protective Materials. ACS omega, 2 (5), 2214-2223. |
| [20] | Gondaliya, R., Kim, D. W., & Sypeck, D. (2015, November). Improving Damage Tolerance with Energy Absorbing Mesh in Composite Laminates: An Experimental Study. In American Society for Composites 30th Technical Conference (pp. 28-30). East Lansing, MI: Kellogg Center, Michigan State University. |
| [21] | Gondaliya, R. B. (2016). Improving Damage Tolerance of Composite Sandwich Structures Subjected to Low Velocity Impact Loading: Experimental and Numerical Analysis. |
| [22] | Shargawi, A. A. (2020). Mechanical testing and evaluation of D3O® material for adequacy of an ergonomic intervention for vibration transmission reduction in aircraft manufacturing (Doctoral dissertation, Wichita State University). |
| [23] | Shargawi, A. A., Amick, R. Z., Jorgensen, M. J., & Asmatulu, R. (2021). Experimental Investigation of Energy Absorbency and Dampening Characteristics of D3O® Material during Low Velocity Static Impacts. J Ergonomics. S, 5. Doi: 10.35248/2165- 7556.21.s5.003. |
| [24] | Bachmann, H., & Weber, B. (1995). Tuned vibration absorbers for “lively” structures. Structural Engineering International, 5 (1), 31-36. |
| [25] | Ren, X. J., Smith, C. W., Evans, K. E., Dooling, P. J., Burgess, A., Wiechers, J., & Zahlan, N. (2006). Experimental and numerical investigations of the deformation of soft materials under tangential loading. International journal of solids and structures, 43 (7-8), 2364-2377. https://doi.org/10.1016/j.ijsolstr.2005.07.013. |
| [26] | Nassef, M. G., Elkhatib, A., & Hamed, M. (2015). Correlating the vibration modal analysis parameters to the material impact toughness for austempered ductile iron. Materials Performance and Characterization, 4 (1), 61-72. https://doi.org/10.1520/MPC20150004. |
| [27] | Ozkaya, N., Nordin, M., Goldsheyder, D., & Leger, D. (2012). Fundamentals of biomechanics (pp. 221-236). USA: Springer. |
| [28] | Klimanek, P., & Pötzsch, A. (2002). Microstructure evolution under compressive plastic deformation of magnesium at different temperatures and strain rates. Materials Science and Engineering: A, 324 (1-2), 145-150. https://doi.org/10.1016/S0921-5093(01)01297-7. |
| [29] | Wu, J. H., Li, C. H., Chiu, H. T., & Shong, Z. J. (2008). Dynamic properties of rubber vibration isolators and antivibration performance of ethylene–propylene–diene monomer/nylon 6 blend systems. Journal of applied polymer science, 108 (6), 4114-4121. https://doi.org/10.1002/app.28070. |
| [30] | Cherng, J. G., Eksioglu, M., & Kızılaslan, K. (2009). Vibration reduction of pneumatic percussive rivet tools: mechanical and ergonomic re-design approaches. Applied ergonomics, 40 (2), 256-266. |
APA Style
Anas A. Shargawi, Michael J. Jorgensen, Nils A. Hakansson, Ryan Z. Amick, Ramazan Asmatulu. (2023). Energy Absorbency and Impact Resistance of D3O® Materials Under Dynamic Impact Loadings. American Journal of Aerospace Engineering, 10(1), 1-10. https://doi.org/10.11648/j.ajae.20231001.11
ACS Style
Anas A. Shargawi; Michael J. Jorgensen; Nils A. Hakansson; Ryan Z. Amick; Ramazan Asmatulu. Energy Absorbency and Impact Resistance of D3O® Materials Under Dynamic Impact Loadings. Am. J. Aerosp. Eng. 2023, 10(1), 1-10. doi: 10.11648/j.ajae.20231001.11
AMA Style
Anas A. Shargawi, Michael J. Jorgensen, Nils A. Hakansson, Ryan Z. Amick, Ramazan Asmatulu. Energy Absorbency and Impact Resistance of D3O® Materials Under Dynamic Impact Loadings. Am J Aerosp Eng. 2023;10(1):1-10. doi: 10.11648/j.ajae.20231001.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.ajae.20231001.11,
author = {Anas A. Shargawi and Michael J. Jorgensen and Nils A. Hakansson and Ryan Z. Amick and Ramazan Asmatulu},
title = {Energy Absorbency and Impact Resistance of D3O® Materials Under Dynamic Impact Loadings},
journal = {American Journal of Aerospace Engineering},
volume = {10},
number = {1},
pages = {1-10},
doi = {10.11648/j.ajae.20231001.11},
url = {https://doi.org/10.11648/j.ajae.20231001.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.ajae.20231001.11},
abstract = {Hand-held power tools, such as percussive riveting tools, produce vibrational forces that are transmitted through the hands, arms, and elbows. These vibrational forces may be responsible for the causation of short and long-term neuronal and/or vascular diseases. Personal protective materials are available commercially, some of which are used during the operation of percussive power tools (e.g., anti-vibration gloves). In previous studies, D3O® materials showed a greater absorption of impact energy in low-velocity static impact testing compared to conventional materials. In this study, D3O® materials were tested under dynamic impact loadings to evaluate resistance to impact characteristics to assess the adequacy of an ergonomic intervention using D3O® materials. An experiment was performed to evaluate material resistance to impact by evaluating the peak load values with different precompression magnitudes and loading frequencies. D3O® materials showed that compression magnitude was a statistically significant factor (p = 0.00) affecting the peak load value compared to loading frequency, which had little to no effect when tested under 14 Hz or less. As peak loads increase, the resistance to impact loading decreases and energy transmission increases. D3O® back protector (DBP) and D3O® Rifle Harness (DRH) exhibited lower peak values compared to D3O® Recoil Pad (DRP) material. D3O® materials may be considered to be utilized in a riveting and bucking intervention to reduce vibrational forces from percussive tools in a dynamic aircraft manufacturing environment.},
year = {2023}
}
TY - JOUR T1 - Energy Absorbency and Impact Resistance of D3O® Materials Under Dynamic Impact Loadings AU - Anas A. Shargawi AU - Michael J. Jorgensen AU - Nils A. Hakansson AU - Ryan Z. Amick AU - Ramazan Asmatulu Y1 - 2023/01/17 PY - 2023 N1 - https://doi.org/10.11648/j.ajae.20231001.11 DO - 10.11648/j.ajae.20231001.11 T2 - American Journal of Aerospace Engineering JF - American Journal of Aerospace Engineering JO - American Journal of Aerospace Engineering SP - 1 EP - 10 PB - Science Publishing Group SN - 2376-4821 UR - https://doi.org/10.11648/j.ajae.20231001.11 AB - Hand-held power tools, such as percussive riveting tools, produce vibrational forces that are transmitted through the hands, arms, and elbows. These vibrational forces may be responsible for the causation of short and long-term neuronal and/or vascular diseases. Personal protective materials are available commercially, some of which are used during the operation of percussive power tools (e.g., anti-vibration gloves). In previous studies, D3O® materials showed a greater absorption of impact energy in low-velocity static impact testing compared to conventional materials. In this study, D3O® materials were tested under dynamic impact loadings to evaluate resistance to impact characteristics to assess the adequacy of an ergonomic intervention using D3O® materials. An experiment was performed to evaluate material resistance to impact by evaluating the peak load values with different precompression magnitudes and loading frequencies. D3O® materials showed that compression magnitude was a statistically significant factor (p = 0.00) affecting the peak load value compared to loading frequency, which had little to no effect when tested under 14 Hz or less. As peak loads increase, the resistance to impact loading decreases and energy transmission increases. D3O® back protector (DBP) and D3O® Rifle Harness (DRH) exhibited lower peak values compared to D3O® Recoil Pad (DRP) material. D3O® materials may be considered to be utilized in a riveting and bucking intervention to reduce vibrational forces from percussive tools in a dynamic aircraft manufacturing environment. VL - 10 IS - 1 ER -
Email: